MHD F-Series version.1.46b [free]

The MHD Flasher F-Series is a complete flash tuning app for your BMW. Unlike a piggyback module, it is capable of complete DME remapping while retaining all OEM safety
mechanisms. This allows for maximum performance,maximum safety, and unrivaled drivability.
Several thousand customers worldwide have been enjoying the number one flash tuning tool for the E series N54 and N55 platforms (MHD Flasher N54 / N55 E-series) since
2015.
---------------------------------------------
Full OBD Flashing:
You can install MHD right at home and start tuning immediately! There is no need to remove and send out your DME for a costly “unlock.” Simply download the MHD Flasher
F-Series app that connects via a K+DCAN cable to your Android device and your vehicle’s OBD-II port, start the app, and within 25 minutes the initial installation is
complete. Further map changes are much faster - only 3 minutes! You can revert your vehicle to the factory OEM flash at any point, and no initial backup is
necessary.
---------------------------------------------
Stage 1, Stage 2 und E85 OTS (Off The Shelf) Maps by PureBoost:
We offer a wide selection of OTS maps for the N55 PWG, N55 EWG and S55 engines suitable for many different vehicle modifications and octane levels. They have been
extensively road and dyno tested, just flash and go!
N55 EWG (Vehicles built after 07/2013 with electronic wastegate):
- Stage 1 (up to 360HP/540NM) - 91oct/95ron, 93oct/98ron, 95oct/102ron, for stock cars. (not available for M2 and X4 M40i)
- Stage 2 (up to 390HP/580NM) - 91oct/95ron, 93oct/98ron, 95oct/102ron, for cars equipped with an upgraded intercooler or high-flow downpipe.
- Stage 2+ (up to 430HP/630NM) - 91oct/95ron, 93oct/98ron, 95oct/102ron, for cars equipped with an upgraded intercooler and high-flow downpipe.
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
N55 PWG (pneumatic wastegate):
- Stage 1 (up to 340HP/540NM) - 91oct/95ron, 93oct/98ron, 95oct/102ron, for stock cars. (not available for M2 and X4 M40i)
- Stage 2 (up to 370HP/580NM) - 91oct/95ron, 93oct/98ron, 95oct/102ron, for cars equipped with an upgraded intercooler or high-flow downpipe.
- Stage 2+ (up to 400HP/630NM) - 91oct/95ron, 93oct/98ron, 95oct/102ron, for cars equipped with an upgraded intercooler and high-flow downpipe.
- Ethanol Mix Maps: Stage 1, 2 and 2+ E20 Maps for ethanol blends of 20%
S55 (BMW M3 / M4 F8x):
- Stage 1 (up to 530HP/700NM) - 91oct/95ron, 93oct/98ron, 95oct/102ron, for stock cars.
- Stage 2 (up to 560HP/780NM) - 91oct/95ron, 93oct/98ron, 95oct/102ron, for cars equipped with high-flow downpipes.
---------------------------------------------
Monitor your engine behavior to make sure it is running perfectly using a configurable and very responsive gauge layout. 50+ engine parameters are available at a
glance!
These are some of the available monitors:
- Boost, Boost Target
- Lambda (AFR)
- Intake Air Temp (IAT)
- Ignition Timing per Cylinder
- Coolant Temperature
- Oil Temperature, Oil Pressure
- Transmission Temperature
- High Pressure Fuel Pump (HPFP)
- Throttle Position
- Wastegate Duty-Cycle (WGDC)
- RPM
- Speed
- EGT
And many more…
MHD exclusive advanced monitor:
- Timing Corrections per Cylinder
- Base Compressor Axis: Boost Setpoint, MAF req WGDC.
- Active Torque Limiters
And many more…
Flash Options:
- Exhaust Burble: duration, aggressiveness and min. speed
- Cold start noise reduction
More options will follow with new updates.
---------------------------------------------
Supported Cars:
M135i F2x N55 2012 - 2016
M235i F2x N55 2013 - 2016
M2 F87 N55 2015 - 2018
335i N55 F3x 2011 - 2015
435i N55 F3x 2013 - 2016
535i / GT N55 F1x 2010 - 2017
640i N55 F0x 2011 - 2017
740i N55 F0x 2012 - 2015
X3 35i N55 F25 2010 - 2017
X4 35i / M40i N55 F26 2014 - 2018
X5 40i N55 F15 2013 - 2018
X6 40i N55 F16 2014 - 2018
M3 S55 F80 2014 - 2018
M4 S55 F82 2014 - 2018
M4 S55 F83 2014 - 2018
X-Drive is supported on all cars.

• 02/11/2020: MHD F-Series version.1.46b
• 09/30/2018: MHD F-Series version.1.01
• Report a new version