ScanMyOpel 1.0.25 [paid]

Full version of ScanMyOpel software for Opel/Vauxhall diagnostics.
It is primarily targeted for Opel car enthusiasts to let them diagnose their own cars.
!!!!Models with CAN bus (Astra H, Vectra C, Astra J, Insignia, Zafira-B, etc) are not supported by this application!!!!!
Check out our new app for the newer models:
https://play.google.com/apps/testing/com.ScanMyOpelCAN2.Main
Now in English, Russian, Hungarian, Polish, German, Finnish, Spanish, Czech and Italian!
Now with Engine, Automatic transmission, ABS, SRS, Power Steering diagnostic and BCM support!
The only Opel/Vauxhall/Holden diagnostic tool for Android!
ScanMyOpel features include:
- native support of Electronic control units used in Opel/Vauxhall cars, which distinguishes ScanMyOpel from many other diagnostic applications providing only limited
generic OBDII support
- monitoring various dynamic parameters of engine, automatic transmission, ABS, EHPS and other ECUs
- reading of static data: ECU identification, fault codes with their current statuses and symptoms
- clearing of fault codes
- Displaying environment information on trouble codes where applicable
- Displaying nominal values of livedata parameters where applicable
- Displaying Livedata parameters charts (only 5 charts can be viewed simultaneously)
- Actuator tests for selected ECUs.
Fault code status meanings:
red - present
yellow - intermittent
green - not present
Current software version supports ONLY the following Opel/Vauxhall models:
- Agila A
- Astra F (MY96+)
- Astra G
- Corsa B (MY97+)
- Corsa C
- Frontera A (25TDS engine)
- Frontera B (X22DTH/Y22DTH engines only)
- Meriva A
- Omega B (MY97+, except X25XE/X30XE/X20SE/Y25DT engines)
- Speedster
- Tigra (MY97+)
- Tigra B
- Vectra B
- Zafira A
The ECU type is detected automatically.
During actuator tests it is possible to monitor livedata parameters. Actuator test lasts 30 seconds, then it stops automatically. User can stop test at any time before 30
seconds expired.
ScanMyOpel supports ELM327-based Bluetooth or WiFi interfaces on all Android devices. Please note - could be compatibility issues with some noname ELM327 interfaces. If
you are experiencing problems with establishing stable connection with the ELM327 interface, please send us the log files and screenshots.
Recommended ELM327 version is 1.4/1.4+. Proper connection with Chinese versions of ELM327, other then 1.4, is not guaranteed. Also, mini-OBD chinese interfaces in general
do not work properly.
Recommended interfaces:
http://www.opel-scanner.com/forum/index.php?topic=2574.0
Also, in case of any issues it is possible to save log and forward it on [email protected] for troubleshooting. Log creating can be enabled from the application menu.
Log files will be stored on the SDCard in "ScanMyOpel" folder.
Attention!!
Since in ELM 327 is used only pin 7, you may not et connected to other modules, which are connected to other pins in the OBD plug. In order to benefit all features of
ScanMyOpel application, please connect together pins 7, 3 and 12 in the ELM327 adapter.
Please try our free Lite version to see if your car is being supported properly BEFORE purchasing the full version.
*** Feel free to email ([email protected]) us directly for issues and support before commenting with low ratings. Thanks! ***
Support forum can be found here:
http://www.opel-scanner.com/forum/index.php?board=40.0

• 11/12/2017: ScanMyOpel 1.0.25
• Report a new version